Wave Soldering Machine

BGA Rework Station DH-A01(Manual)

Page Under Construction

Features

  • Page under construction

Selective soldering

BGA Rework Station DH-A01(Manual)

Page Under Construction

Features

  • Page under construction

Soldering/Desoldering Station

BGA Rework Station DH-A01(Manual)

Page Under Construction

Features

  • Page under construction

Soldering Accessories

BGA Rework Station DH-A01(Manual)

Page Under Construction

Features

  • Page under construction

BGA Rework Station

BGA Rework Station DH-A01(Manual)
Model:DH-A01(Manual)
PCB SizeMax: 300 mm X 300 mm
Min: 20 mm X 20 mm
BGA size5 mm X 5mm – 55mm X 55mm
Power Input Power supply  : AC220V±10% 50/60Hz
Power of Operation : 2600W
Top heater                   : Hot air 800W
Bottom heater           : IR 1800W
Machine Footprint470 X 400 X 450 mm.

Features

  • Two independent heaters, all can set 8 segments heating, cooling and constant temperature, can store 10 groups of temperature profile. IR preheat area can be controlled according to PCB size
  • K sensor close loop control and automatic temperature compensation system. It combines with temperature module, which enables temperature accuracy to ±2°C
  • Movable heater, easy to operate
  • Hot air nozzles, 360 degree rotation, easy to install and replace, customized is available
  • V-groove PCB clamp + Universal fixture for rapid, convenience and accurate positioning that fits for all kinds of PCB board
  • Powerful cross flow fan, cooling the PCB board efficient after heating, to prevent it from deformation
  • Sound hint system. There is an alarm before the completion of each desoldering and soldering
BGA Rework Station DH-5830
PCB SizeMax: 405 mm X 370 mm
Min: 20 mm X 20 mm
BGA size2 mm X 2mm – 80mm X 80mm
Power Input Power supply  : AC220V±10% 50/60Hz
Power of Operation : 4500W
Top heater                   : Hot air 800W
Lower heater              : 1200W
Bottom heater           : 2400W
Machine Footprint535 X 650 X 600 mm.

Features

  • With vacuum tube to pick up the bga chip conveniently
  • Real-time settings and actual temperature profile display can be used to analyzed and correct parameters
  • External temperature sensor enables temperature monitoring and accurate analysis of real time temperature profile
  • Adopt three heating zone, upper and low heater hot air, bottom heater is infrared preheating zone
  • K type close loop control, the temperature accuracy will be on ±2°C
  • High power cross flow cooling fan, prevent the PCB from deformation
  • Sound hint system: there is voice reminder 5s-10s before the completion of heating, to get the operator prepared
  • Security measure: overheat guard and emergency stop function
BGA Rework Station DH-A1L
PCB SizeMax: 500 mm X 400 mm
Min: 22 mm X 22 mm
BGA size2 mm X 2mm – 80mm X 80mm
Power Input Power supply  : AC220V±10% 50/60Hz
Power of Operation : 5000W
Top heater                   : Hot air 800W
Lower heater              : 1200W
Bottom heater           : 2700W
Machine Footprint800 X 900 X 750 mm.

Features

  • Uses LED monitors to control-all the data adjustments, control and display are digitally presented in clear and convenient fashion
  • This machine uses dual temperature control with wind heating for the upper part and IR heating for the lower part. Heating time, temperature and all relevant data are all displayed on the monitor
  • It uses precise K-type close circuit control and automatic temperature adjustment system, with temperature module to enable precision temperature control of ±2 degC. External temperature sensor enables temperature monitoring and accurate analysis of real time temperature profile
  • V-groove PCB support for rapid, convenience ad accurate positioning that fits for all kinds of PCB boards
  • Flexible and convenient removable fixture on the PCB board which protects and prevent damage to PCB
  • Various sizes of BGA nozzles, which can be adjusted 360 degree for easy installation and replacement
  • 8 level up (down)+ 8 level constant temperature control, large storage space for temperature profiles, can operate curve analysis, setting and correction errors
  • Including Voice ”early warning” function
  • With USB interface, can be convenient to download the current graph to the USB drive to save up, and you can plug in the mouse using the touch screen using longer hours
BGA Rework Station DH-A2 (Semi - Automatic and Optical)
PCB SizeMax: 450 mm X 400 mm
Min: 22 mm X 22 mm
BGA size2 mm X 2mm – 80mm X 80mm
Power Input Power supply  : AC220V±10% 50/60Hz
Power of Operation : 5200W
Top heater                   : Hot air 1200W
Lower heater              : 1200W
Bottom heater           : 2700W
Machine Footprint600 X 700 X 850 mm.

Features

  • Placement head and heater integrated designing, flexible, convenient,
    shortcut, stable, temperature control and alignment is very precise and you can finish the work coherently
  • Heating system and placement system can go up and down according
    to the setting program(automatic placement and soldering)
  • High Definition Monitor ,imaging is very clear, you can observe every melting joints clearly
  • Precise Optical Alignment System, clear imaging ,maximum magnification is up to 220 times, placement accuracy is +/- 0.01mm
  • USB interface can screenshot the process of temperature profiles In the same time you can insert your mouse so that in the future you can update new programs
  • When temperature is too high, temperature will be adjusted automatically by air reflow, so that no crack for PCB board and no damage peripheral components

    Get a Quote

    Call for a Demo

    Write us your requirement we will get back to you shortly

    You can also email us or call

    Email:

    sales@kyoritsuelectric.com

    Phone:

    Mobile: +91 9552597464